Leaking heat exchanger
Water appearing inside the boiler jacket or under the unit, not from a valve, often means the heat exchanger has failed.
New boiler installation
A new boiler sized from your home's heat loss, not the old nameplate
Many older boilers were oversized from day one. Replacing one is a chance to match capacity to the building, lower fuel use and quiet the system down.
Service ticket: Boiler Replacement
- Heat loss
calculated room by room - Options
condensing, standard and combi - Clean loop
flushing and filtration included
Planning a boiler upgrade
Boiler replacement built around the system you already have
Replacing a boiler is a bigger decision than replacing most appliances. The new unit has to fit your existing radiators or baseboard, your venting options, your fuel supply and, in many homes, your domestic hot water needs. It also needs to be sized correctly. A boiler that is far larger than the building requires will short-cycle, waste fuel and wear out sooner, and that is exactly what happens when a new boiler is chosen by copying the old one's rating.
Our replacement process begins with a heat loss calculation. We measure rooms, note window types and insulation levels, and account for the coldest design temperature expected in Agua Dulce, TX. We also measure the output capacity of your existing radiators or baseboard, because that emitter capacity determines what water temperatures the system needs to keep the house warm. Those two numbers together guide the equipment choice.
Condensing, non-condensing and combi boilers
Condensing boilers extract extra heat by cooling their exhaust gases until water vapor condenses. They reach high efficiency, but only when return water comes back cool enough. Systems with generous radiator capacity or radiant floors are excellent candidates. Condensing boilers vent with plastic pipe through a side wall or roof and produce acidic condensate that is routed through a neutralizer to a drain.
Non-condensing boilers remain a sensible choice for some older systems, particularly those that need high water temperatures or where venting through the side wall is impractical. Combi boilers heat both your radiators and your tap water on demand, saving space in homes where a separate water heater is not needed. They work best when hot water demand is moderate, and we will be honest if your household's usage suits a separate tank better.
Steam systems are a special case. They generally need a new steam boiler, sized to the radiation connected to it and piped with proper near-boiler headers. Converting steam to hot water is possible but is a larger project involving the piping throughout the house.
Installation details that protect the new boiler
A new boiler connected to old piping inherits whatever sludge and debris the old system accumulated. We flush the loop and, where appropriate, add a dirt separator or magnetic filter to keep the new heat exchanger clean. Outdoor reset controls adjust water temperature to the weather, which improves comfort and allows condensing boilers to condense more often. Venting, gas piping and combustion air are installed to the manufacturer's instructions and local code.
If you are switching from a chimney-vented boiler to a sidewall-vented model, any water heater still using the chimney needs to be evaluated, since the chimney may no longer draft correctly for a single small appliance. We check that as part of the job. Homeowners weighing a different heating approach altogether can compare a Heat Pump Installation alongside the boiler options, and we can explain where each makes more sense. If your current boiler still has life in it, Boiler Repair may be the smarter step for now.
Late spring and summer are the most practical seasons to replace a boiler in Agua Dulce, TX. The house can go without heat for a day or two with no discomfort, crews have more scheduling flexibility, and any venting or piping changes can be completed without time pressure. Replacing an aging boiler in the middle of winter is possible but usually means working around a no-heat emergency. If your boiler is showing its age, a heat loss assessment during the off-season lets you choose equipment calmly and schedule the work on your terms.
What drives the cost of a new boiler
| Boiler type and efficiency | Condensing and combi boilers cost more than standard units but can reduce fuel use. Steam boilers are priced by the radiation they must serve. |
|---|---|
| Venting and piping changes | New sidewall venting, chimney liners, condensate drains and near-boiler repiping add labor and materials. |
| System condition | Heavily sludged systems, failed zone valves or corroded piping may need attention so the new boiler is not damaged. |
Indicators that your boiler is nearing replacement
Rising fuel bills
Older boilers lose efficiency as heat exchangers scale up and burners wear, so the same comfort costs more each season.
Frequent repairs
When calls become an annual event and parts get harder to find, replacement usually becomes the more economical path.
Uneven heat throughout the house
An oversized boiler that short-cycles or controls that cannot modulate can leave some rooms too hot and others cold.
Corrosion and flue damage
Rust on the jacket, flue pipe or burner area can signal condensation problems or venting issues that affect safety.
A boiler more than a few decades old
Age alone is not a reason to replace, but older units lack the efficiency and controls of modern equipment.
How a boiler replacement project runs
Assessment and heat loss
We measure the home, inventory radiators or baseboard, inspect piping, venting and fuel supply, and discuss hot water needs.
Equipment recommendation
Based on the numbers, we recommend a boiler type and size and present written options with flat pricing.
Permits and preparation
We arrange required permits and plan the removal, venting route and near-boiler piping before installation day.
Removal and installation
The old boiler is drained and removed, the loop flushed, and the new boiler piped, vented, wired and filled.
Startup and tuning
We purge air, set controls and outdoor reset, test combustion, verify every zone heats, and show you how the system works.
Before your appointment
- Collect any records for your current boiler, including the model number and past service notes.
- Think about your household's hot water use, especially if you are considering a combi boiler.
- Make room around the boiler, water heater and any path the old unit will take out of the house.
Boiler replacement questions answered
Not necessarily. Many older boilers were oversized. A heat loss calculation often shows a smaller boiler will heat the home better, with longer, steadier cycles.
Often yes. Cast iron radiators have large surface area and can heat the home with lower water temperatures much of the season, which lets a condensing boiler run efficiently.
Most residential replacements take one to three days, depending on venting changes, piping modifications and whether the system needs flushing.
Yes, either with a combi boiler that heats water on demand or with an indirect water tank heated by the boiler. We help you choose based on your usage.
We drain it, disconnect it and remove it from the property as part of the installation.
Usually not. Cast iron radiators and most baseboard can be reused with a new boiler. We check for leaks, failed valves and sections that no longer heat, and we measure their output because it determines the water temperatures the new boiler will run.
Start planning your new boiler
Call to schedule a heat loss assessment. You will get sizing numbers, clear options and a flat price in writing.
Prefer to browse first? Start from Home.